Wednesday, October 9, 2013

Vertical Launching Systems and the Type 26




Much discussion has been caused by the Type 26 model shown at DSEI 2013, as this new model showed just 16 VLS Strike Length cells instead of the 24 shown earlier at Euronaval 2012. Reportedly, the main reason behind the difference is the fact that at Euronaval the model was fitted with the European SYLVER VLS system, while the DSEI model was fitted with the American MK41.
Why the very noticeable difference? 

In this photo by Navy Recognition, the Type 26 model seen at Euronaval 2012: there are 24 SYLVER A70 cells
 
The photo from DSEI 2013, showing only 16 cells, MK41 Strike Lenght. Overlayed in red, the big question: is there under-deck space for fitting two more MK41 modules, replacing the CAMM cells? The deck area is not a problem, but space under deck might be, as CAMM cells only go around 3 meters deep, while MK41 Strike would go down over twice as much.


MK41

The MK41 vertical launch system was conceived in 1976 and first appeared on the cruiser USS Bunker Hill. The vertical launch system, conceived by FMC but produced by Martin-Marietta (now part of Lockheed Martin), was a major upgrade from the MK26 launcher, which employed a twin-arm ramp with an under-deck ammunition depot for 44 missiles. The same space occupied by a MK26 launcher, thanks to the MK41, became a 61-missiles silo, with all missiles constantly ready to be fired, against only 2 ready to fire on the arms of the MK26 ramp. 


Two graphics showing the complex MK26 twin-arm launcher that the MK41 replaced.Missiles were vertically struck down in the two conveyors, and vertically pushed up onto the launcher's two arms.
 
The MK41 comes in modules which have 8 missile cells each, arranged in two rows of four aligned on the two sides of a vertical uptake used for venting hot gas. Originally, there was also a module with just 5 missile cells, with the space of the other three occupied by a fold-down crane for at sea reloading, as we’ll see. 

 
MK41 quick overview. Also shows the two large multi-module silos on Arleigh Burke-class ships

Each module carriers its own launch sequencer, motor control panel and gas exhaust system. When a missile is fired, it exhausts downwards through the blowout bottom end of its canister; the hot gas goes down into the MK41’s plenum and then vents upwards through the uptake, which has its own hatch opening between the two rows of cells.
The plenum can withstand 7 launches from each cell, plus a restrained firing with full motor burn from any other cell. A deluge system is installed to provide flooding of missile cells to prevent warhead explosions. 

The uptake hatch between the two rows of four cells is very evident in this image, showing the launch of a Tomahawk. Notice the high pressure, high-temperature gas venting upwards from the hatch.
 
Multiple MK41 8-cell modules can be assembled together in a silo: Ticonderoga class cruisers were built with two large silos, each containing seven 8-cell modules plus, originally, a 5-cell plus crane module, giving the ship a total of 122 missile cells. 

What looks like a 5+crane MK41 module is being lowered into the silo, to join three 8-cell modules already in position. Note the density of the installation. A further four 8-cell modules will follow, to form a 61 cell large silo.
 
A 61-cell silo, completed, with a caniser being lowered towards an empty cell. Note the 3-cell wide hatch of the crane, in the second module from the bottom, to the right of the image.
On the DDG-51 Flight I and II, the MK41 modules were arranged in a silo with 29 cells on the bow (the equivalent of three cells taken up by the crane) and 61 on the stern. 

The All-Up Round missiles used in the MK41 come in sealed canisters which are used for storage, transportation, handling and, ultimately, for launch. Once a canister is struck down into a VLS cell, it becomes an integral part of the launcher system. Each canister has a common external envelope to support system launcher module interfaces, while internal mechanical and electrical components are tailored to specific missile shapes and interface requirements. In other words, to each missile, its own canister:

MK13 canisters are for Standard SM-2 series missiles;
MK14 canisters are for Tomahawk
MK15 canisters are for ASROC
MK21 canisters are for SM-3 anti-ballistic missiles
MK22 canisters are for Sea Sparrow
MK25 is the special, quad-pack canister for ESSM 

There are successive variants of the canisters. Today, the Tomahawk All-Up-Rounds come in MK14 Mod 2 canisters. Before it came the Mod 1, which had a launch security device for the control of Tomahawk employment, and by the Mod 0, which had a key-operated security device against unwanted launches, as it was meant to carry the now withdrawn nuclear-tipped Tomahawk.
The canister MK21 Mod 3, instead, is a slightly modified MK21 used with the new Standard SM-6 missile.

Canisters have a shell structure is a steel weldment with corrugated steel skins and cast steel end frames. They are fitted with a variety of vital equipment and characteristics, including: adjustable lateral restraint shoes, longitudinal shock isolators, an ablative coated steel baseplate structure, ablative blocks, deluge piping, nitrogen fill piping, cables, a code plug and a Canister Safe and Enable Switch. The Canisters also contain a telemetry antenna and monitoring connection.
The canisters are not simple boxes. They contain precious equipment, and the missile cannot do without its canister. 

Open MK41 cell hatches, showing the empty shafts. Without canisters, the MK41 is little more than a metallic frame.

An overview of the MK14 canister, employed by Tomahawk

The Tactical Lenght MK15 canister, containing the ASROC missile, and showing the MK18 canister adapter that allows the use of shorter canisters in the Strike Lenght cells

Inserting a canister down a MK41 cell

MK41 comes in different lengths, which determine the size of the canisters that can be installed and, consequently, decide which weapons can be integrated.
The canisters have a square base, with a total diameter of 25 inches. Inner diameter of the space for the missile is around 22 inches. There are three canister sizes:

-          170 inches; for self-defense weapons only (Sea Sparrow, ESSM)
-          228 inches; add SM-2 and ASROC
-          264 inches; add Tomahawk, SM-3

These canisters fit into into different length MK41 launchers, obviously. This value refers, effectively, to the heights of the modules to be installed in the ships.

-          Self Defense Launcher is 209 inches
-          Tactical launcher is 266 inches
-          Strike launcher is 303 inches

The Tactical Length canisters, however, can be and are fitted into Strike Length cells with the aid of the MK18 Canister Adapter, a steel weldment with appropriate dog-down connections that serves as a conduit for rocket motor exhaust vented to the plenum. Fitted to the bottom of the shorter canister, it allows it to fit easily down like it was a strike-length canister.   

The deck area of a 8 cell module, instead, remains the same. The short side of the launcher is 81.75 inches, while the long side is 124.63 inches. Depending on their height, empty 8-cell launcher modules weight 26.800 lbs or 29.800 lbs or 32.000 lbs for the Strike Length launcher. 

The old 5-cell plus crane MK41 module. This is no longer produced or employed, as the crane never worked as well as hoped. It remains an impressive bit of kit, though.
 
Using the crane at sea for reloading

The fold-down crane for at-sea reloading of missile cells was contained under deck in a space equivalent to just 3 missile cells, and elevated outwards during reload operations. The requirement was for the replenishment of 10 VLS cells per hour, even in Sea State 5, with the missile canisters being transferred via RAS (UNREP for the Americans) rigs.
Reloading of missile canisters at sea, however, proved always difficult at best, and the ingenious crane, albeit fascinating, was never capable to deal with the larger and heavier canisters, such as the MK14 containing the Tomahawk. The failure of the VLS replenishment at sea is summarized as follows:


The original development of the MK 41 Vertical Launch System (VLS) for cruisers and destroyers in the late 1970’s included a requirement to replenish ten VLS canisters per hour, day or night in Sea State 5 conditions. The system actually installed consisted of the STREAM rig to transfer the VLS canister to the missile ship sliding padeye; then deck handling the canister to a position where a crane could tilt up the canister over an empty cell and then strike the canister down. The crane was a commercial Swedish folding crane. Three canister cells were combined to make stowage for the crane. An elevator raised or lowered the crane. The at sea VLS Unrep technical evaluation discussed in Miller (1992) identified that the crane did not have the capacity to lift Tomahawk VLS canisters; SM-2 VLS transfer rate was three per hour and the pendulum action of the crane limited Unrep to Sea State 3 conditions. The cranes are now in layup.


Eventually, the ambitions of at sea reloading of MK41 cells were abandoned, and the DDG51 of the Flight IIA were never fitted with the crane, instead getting 32 and 64 cells silos. The cranes were at times used during Desert Storm, to aid the correct placement of missile canisters. Desert Storm, in 1991, provided the US Navy with the first experience of wartime reloading of warships fitted with MK41: the USS John Paul Jones was the first warship to receive a wartime reload of Tomahawk missiles, but did so while pierside in Mina Jebel Ali, in the United Arab Emirates.
The closest thing to an at sea wartime reloading was the transfer of shipborne missiles from support vessels to warships in the lee of Masirah, Oman. The ships were motionless in the protected waters, but not moored to the bottom, as it was felt tactically advantageous to be able to move quickly in case of enemy attack.  

Interest in at-sea reloading is not dead, and a solution might come in service in the future, since the impossibility to rearm a major warship without pulling it away from the fight and into enclosed, friendly waters is seen as a major limitation. The logistics of VLS reloading are complex, and require extensive material handling mechanical equipment, time and adequate portside or shipborne facilities. The new Upper Harbor rearming facility built by the Royal Navy at Portsmouth is a good example of structure thought specifically for the replenishment of VLS cells. 

The new, specialized rearming facility built for Royal Navy use, with the two cranes for VLS reloading.
 
During war operations abroad, having at hand such a well-equipped facility could be a real problem, as US documents have underlined for decades.

"double-ended" VLS ships such as AEGIS cruisers and destroyers can be rearmed twice as fast if two cranes are available (a frequent bone of contention at stateside weapons stations). With both cranes swinging canisters and enough forklifts and pier-side handlers to keep up with them, a motivated AEGIS crew can completely reload the ship's VLS systems in one (long) day. Note the optimum requirements, though: a pier of sufficient length and with water alongside to accommodate ships up to 563 feet long and 32+ feet in draft; cranes, forklifts, trucks, and/or flatbed rail rolling stock; and contiguous or near-contiguous cargo ports or airfields. Such a facility is precisely the kind of "logistics node" that the JFMCC will be attempting either to defend or seize early in a regional conflict. When in friendly hands, such a facility is a prime TBM target in its own right, as seen at Jubayl, Saudi Arabia, on 16 February 1991, when an Iraqi Scud impacted within yards of an ammunition pier berthing seven ships, a supply barge, and the USS Tarawa.

An at-sea rearming technique and equipment is part of US Navy ambitions to modernize Underway Replenishment (UNREP) technology, effects and methods. The following describes one of the possible approaches:


The concept for replenishing 15 VLS per hour in Sea State 5, shown in Figures 9, 10, 11 and 12 centers around a transportable VLS rearming device that is stowed and maintained on the Combat Logistics Force (CLF) ship. When the combatant ship comes alongside for at-sea rearming or load adjustment, the rearming device is transported from the CLF ship by the new Heavy Unrep rig to the combatant ship sliding padeye along with a team to operate the rearming device. A swing arm at the base of the sliding padeye is used to position the rearming device onto three low profile rails permanently mounted atop the VLS launcher. A hydraulic power unit on the combatant ship powers the swing arm and also the rearming device after it is on the rails. 

The CLF ship will next transfer a loaded VLS canister to the sliding padeye. The canister will be lowered to the swing arm by the sliding padeye and then be released from the transfer rig. The canister will be swung around and be picked off from the swing arm by the rearming device two clamp rings. The canister will be moved by the rearming device to a position over an empty cell. The cell hatch will open and the rearming device will erect the canister to the vertical. The canister will be lowered by a wire rope hoist into the cell. The rig will be disconnected from the end of the canister, the cell hatch will close and the canister will be connected below decks to the VLS circuits. When the VLS rearming or VLS load adjustment is completed, the rearming device and team will be returned to the CLF ship.

 
The above proposal puts the VLS reloading equipment and specialized team not on the warship, as with the early crane, but on the Logistics Ship. The team and the rearming device will move on to the warship to ream at the beginning of each evolution, and will move back to the support vessel at the end.

The threat of Anti-Access and Area Denial strategies and the focus on the Pacific should both work as powerful budget and strategy drivers in the next few years to encourage the US Navy to bring work forwards on UNREP improvement. At sea logistics will be more important than ever, and we can expect to see big increases in capability.
It is worth noticing that the Heavy UNREP equipment envisaged and experimented by the US Navy appears to be very similar to the Heavy RAS equipment being experimented by the Royal Navy at HMS Raleigh in anticipation of adoption on the next generation Solid Support Ships. The wide loads being moved, in terms of bulk, and the weight mentioned (12.000 lbs) are roughly the same values indicated for the Rolls Royce H-RAS. 

 
The US Heavy UNREP equipment
 
The H-RAS facility at HMS Raleigh, in one photo from Dave Sheffield. According to the blog NavalMatters, we can expect an article on the H-RAS activities in november's edition of Navy News. The shuttle resembles that seen in the 12.000 pound mode of the Heavy UNREP kit for the US Navy, but no actual heavy load can be seen. Trials are still at an early stage

A Mk14 Mod 2 Tomahawk canister comes at 6130 pounds. Both the H-RAS and H-UNREP kit would move possibly two canisters per each lift, with a rhythm as high as 25 lifts per hour. While at-sea rearming of Royal Navy VLS ships is not on the cards, the new Solid Support vessels seem set to have the RAS capability to keep the door open for future adoption of adequate kit and methods.


SYLVER   

The European SYLVER vertical launch system follows the same principles of the MK41, but has been developed more recently, has never had any built-in at-sea reloading kit, and has made some different choices. Getting details on SYLVER is much more complex than getting adequate information on MK41, and it has taken me quite a while to collect information which is not yet as complete as I’d like.

SYLVER comes in three main sizes, in addition to the very small, self-defense for small ships A35 launcher. The main modules are the A43, A50 and A70. The number refers to the approximate length of the cells, which vary from 4.3 meters to 7 meters, roughly matching the MK41 Self Defense, Tactical and Strike lengths. The A43 launcher has a total height of 5.3 meters; the A70 is 7.6 meters tall.

DCNS, the maker of SYLVER, proudly notes that SYLVER is significantly lighter than MK41. Early claims were of 30 to 40% weight savings thanks to the use of more modern materials and composite, but this seems over-optimistic, as the declared weight of the 8-cell standard modules goes from 8 tons (A43) to 12 tons (A70).
SYLVER has a smaller deck area footprint, of 2.6 meters x 2.3 meters, while vaunting an exhaust duct which, according to DCNS, is 1.5 times larger than that of the MK41. The larger duct is meant to make the system even safer by expelling gas at lower pressure, allowing simultaneous salvo firing even while one missile has an inadverted restrained launch.

The significant difference in width of a 8-cell module (2.6 meters for SYLVER, against 3,17 meters for MK41) explains why the Euronaval 2012 model of the Type 26 had three 8-cell modules fitted abreast, while the DSEI model only had two MK41 modules sitting abreast. The first combination fits in some 7.8 meters, while the same number of MK41 modules arranged in the same way would require 9.51 meters.

The difference, however, comes at a price: the SYLVER’s cells are only 22 inches wide, 3 inches less than the MK41’s. The difference is very significant, as SYLVER of course needs its own canister, and even assuming that these are thinner, the internal diameter available for the actual missile will inexorably be less than 22 inches offered by the MK41 canisters. 

 
The current DCNS brochure says nothing of the detailed sizes of Sylver, but in older documents emerges that the SYLVER cells are 22 inches wide. Early proposals (i don't know if they went ahead or not) included developing the A35 variant using 25 inches cells, to take ESSM quad-packs and compete with MK41 on the export market. Sounds to me already like a bit of an admission that going for a smaller cell wasn't a winner.  An intermediate lenght A6X was also proposed, but never went ahead.

Although DCNS shows Tomahawk as a possible payload for the A70 launcher in its brochure, it is entirely right to question whether it would be actually possible to integrate it in the European cells. The Tomahawk missile is around 20.5 to 21 inches in diameter, so the space available to fit it, complete with a proper canister, into a 22 inches cell is truly minimal.
Integration would be a challenging affair for physical reasons, as well as for politic, economic and combat system reasons. A wholly new canister would have to be designed, and the space available to do everything that needs to be done would be minimal.
Apparently, besides, A70 canisters are circular, not square like MK41’s. 

Loading a SYLVER A70 canister on a FREMM frigate of the french navy, in an image by DCNS. The canister is circular, not square, so more similar to Russian and Chinese systems than to the MK41! 
 
There is also an unanswered question coming to mind when observing the disposition of SYLVER launchers on warships. On each vessel, the 8-cells SYLVER launchers are always in contact at most only by the short side. This can be observed on Type 45, on the Horizon destroyers of Italy and France, on the FREMM frigates and on the Formidable-class frigates of Singapore. The long side of the launcher modules is never in contact: there is always an important space of deck between one launcher and another. 

 
SYLVER A50 modules on the Type 45: two rows of three modules each, touching by the short side, but well distanced when it comes to the long side. 

 
The silo on Horizon-class destroyers. This, specifically, is Italy's Caio Duilio. The 48 launchers are arranged in three rows of 2 modules each. Very different arrangement than Type 45's one, but still there is significant space left between the rows on the long side. Compare all this space to a 4 or 8 module MK41 silo: why all this space wasted?
 
On the italian aircraft carrier, Cavour, in a photo by Chinomar, from the website Mezzi Militari Italiani

On Singapore's FORMIDABLE frigates

On Charles De Gaulle


This is not observed in MK41 silos, which show a very high density, with the separate modules in direct contact. One is left to wonder if the separation between modules is a choice made by all customers so far, or an unavoidable necessity.
Perhaps coming from the fact that the canisters themselves are thinner...? 
If this is the case, the lower deck-area of SYLVER becomes much less of a truth: basically, fitting more SYLVER modules than MK41 ones, in the same deck area, is only possible so long as the modules are installed abreast, like on Type 26. In a large multi-module silo, or in any case when the long sides should touch, a lot of space ends up wasted, for some reason.


The right choice?

It is not easy to judge which system represents the right choice for the Royal Navy. I’ve already discussed in an earlier article about this complex topic, and much of the uncertainty is due to the fact that it is not clear yet what weaponry the RN hopes to fit into the VLS cells. Of course we can assume the Tomahawk in the short to medium term and the SPEAR Capability 5 (also known as UK-FR Future Cruise and Anti-Ship missile) in the longer term (not before 2030).
For the Tomahawk, its eventual successor (American design) and for other possible weapons (LRASM?), the MK41 would be the most appropriate, if not the only choice.
Going for commonality with the US Navy would be, in my opinion, more advantageous and more wise in a long-term analysis, despite the SPEAR 5 work with France. It is very hard to see how investment in SYLVER and in its weapons by UK and France (and eventually Italy) could ever match the level of support and attention that MK41 will receive from the US, Japan and other export customers. In terms of logistics and future-proofing, MK41 would make greater sense.

It is true that it is hard to see at the moment which American weapons, beyond Tomahawk, could ever be selected for the (british) Type 26. With CAMM covering the air defence role, with Sea Viper on Type 45 in the higher tier, it is hard to see british interest for any of the American SAMs for at least a few decades.
When the UK will eventually acquire an anti-ballistic missile capability (because I believe it is a matter of “when it becomes necessary”, more than a question of “if”), we can expect that the Type 45 will be the platform of choice, so being able to embark SM-3 is also not immediately relevant.
As for LRASM, the missile’s future isn’t even certain yet, and the UK will likely not procure it, unless the SPEAR 5 ambitions collapse.
However, there are logistic, support and future-proofing reasons to go MK41. Being tied to the US Navy is the most promising way to ensure that the weapon system is not without support, evolution paths, and new weapons.

I don’t see many reasons to go with the SYLVER. Certainly not Scalp Navale, which is a less performing, more expensive alternative to Tomahawk that the RN frankly does not need at all.
The main cause of interest is the SPEAR Capability 5 missile, but this is little more than a concept, and the few studies started so far are all aimed at a 2030 entry in service, which might easily slip further to the right. If the currently envisaged timelines are respected, the first Type 26 by then will be approaching the first 10 years of service life. Betting it all on a missile that might or might not come by then, does not seem the right way to go.
The main factor, at this point, is the number of VLS cells. Having 24 instead of 16 is obviously much better and preferable under many points of view. The smaller diameter of the cells, however, which already feels tight today, is a concern for the future.
It would be important to know if the Type 26 design can spare the additional under-deck space which would be needed to replace the banks of CAMM-only cells in the bow silo with an additional MK41 module or two. If these is the possibility to do so, as has been suggested to me (but not confirmed by sufficiently authoritative sources), then my suggestion is to go MK41. CAMM could just be quad-packed into some of the MK41 cells, instead of having its own single-purpose spaces.

Even if such space does not exist, I think adopting MK41 could be, in the end, the best choice, although less evidently so. MK41 promises greater certainties for the future: there’s a much larger and richer customer base investing on it, and it has the physical size advantage. You can be reasonably certain than any missile developed for the 22-inches wide SYLVER cell will fit into the 25-inches MK41, while the opposite simply is not true.    

I suspect this is a reason behind MBDA’s decision to offer European missiles for the MK41. Of course, the main reason is the global diffusion of MK41, but I believe it is nonetheless indicative that MBDA has signed an agreement with Lockheed Martin to integrate European missiles in the MK41 cells, starting with the easier system to transfer, the very interesting Sea Ceptor / CAMM. The greater width of the MK41 cell has allowed Lockheed to develop the Extensible Launching System ExLS: a simple, yet ingenious “launcher within the launcher” which can be slid into MK41 cells (or used as a stand-alone system) to accommodate foreign missile systems, with their canisters and launch electronics. When it first appeared, it was associated with plans for quick MK41 integration of smaller weapons and even countermeasures: the NULKA active radar decoy, a quadpack of RAM Block 2 missiles or a pallet of NLOS surface-strike weapons were all shown as possible payloads.
After being demonstrated with NULKA, the ExLS has now come very much back in the spotlight for its instrumental part in allowing MBDA and Lockheed Martin to get to push-through tests with the CAMM missile in a MK41 cell in very short time. After agreeing to collaborate, in May 2013, the two companies have successfully cleared the first launch trials in September: a record for the slow world of defence technology. This success has been just as quickly rewarded by the selection of CAMM in MK41 cells for the upgrade of the ANZAC class frigates of New Zealand.  
 
CAMM test fired out of an ExLS module clipped into a MK41 standard launcher

It is also worth remembering that the US Navy has already invested in a new generation of Vertical Launch System which share the same base principles but comes with longer, wider cells. The MK57 launcher comes in four-cell modules, and is so far only known for being employed by the sole DDG-1000 Zumwalth-class. These three unique ships will have 20 MK57 modules installed, not in dense silos like on Ticonderoga and Burkes, but in peripheral position along the sides of the hull. 
The new launcher is fully compatible with existing MK41 weaponry and canisters, but offers cells which are 283 inches long and 28 inches wide, with a maximum mass of 9020 lbs. It is a very noticeable increase in all parameters from the MK41 Strike Length.
It is not yet evident which new weapons will require this big space, nor is it likely that the MK57 will replace the MK41 anytime soon. For now, it is tied to a new class of warships which has been cut down to just three hulls. It will be interesting to see if the MK57 becomes part of the requirement for the proposed Arleigh Burke Flight III, or for whatever ship comes next.
The US Navy’s belief, however, seem to be that larger missiles are likely, and while the MK57 is possibly too far ahead of the current requirements, the SYLVER might soon enough fall behind requirements. 


46 comments:

  1. Thanks for this, particularly the information regarding Sylver. If it is true that Sylver is thinner it would seem a strange decision as being newer it should also be more future proofed. Not only does being thinner reduce compatibility with foreign missiles and limit the ability to quad pack, but it can also increase the costs of compatible missile systems that push its limits, which might explain Scalp Naval's elevated costs. I wonder whether the decision was down to particular design priorities or technical limitations.

    Radwulf

    ReplyDelete
  2. It does look like the mk 41 launch cells would make the better long term choice, lets see if the MOD agree.

    ReplyDelete
  3. But Type 26s are almost always portrayed in the media as ASW ships. Wouldn't that lean it towards the Mk41?

    ReplyDelete
    Replies
    1. The Type 26's biggest design driver is ASW operations indeed. However, only 8 of a planned 13 ships will be actually kitted for ASW work. And anyway, ASW does not exclude their use in all other operations, both because they can be fine multi-role vessels and because they have to be, especially in a fleet which has become so small. There really is no alternative.

      The only link with ASW, for the MK41, is the ASROC missile, and while it might have the RN interest, it will be hard to obtain funding for it.
      It could still be an argument in support of MK41, but not one particularly strong and immediately effective during tough budget negotiations.

      Delete
    2. What else will the RN have then to to Type 26s? I thought the 8 out 13 stuff was only and all 13 will be for anything.

      Delete
    3. The remaining five Type 26, like today's Type 23, will not have the towed sonar installed.

      Delete
    4. Genuine question - would you prefer 13 type 26 split 8/5 as currently planned or 12, using the savings to ensure they were all kitted out to the same towed sonar ASW standard and that the normal "for but not with" gaps were avoided as well?

      Delete
    5. I think i'd be unwilling to accept any reduction in the number of hulls, considering how few they are as it is.
      Would be a different matter if i could build 10 Type 26 fully kitted, and sacrifice the last three vessels in exchange for 6 smaller, cheaper global corvettes. That i would do.

      Delete
    6. Given that further cuts are likely to be the outcome of SDSR 2015 you have to be more than an optimist to believe that anything like 13 are ever going to be built. I think we are looking at a maximum of 8 ASW and no GP at all. Maybe there will be the opportunity to increase hull numbers with something based on the MHPC design at some point in the future. I sincerely hope I'm wrong, but the way things are looking we will probably lose some T23s in 2015 and this will then pave the way for a force of 14/15 escorts for the longer term.

      Delete
    7. Who knows what will happen with SDSR 2015 (or as it looks now, SDSR 2016). It is possible that there will be small cuts but I don't expect anything too big as the RN has now reached the limit of what cuts can be made before it has to give up trying to do a lot of things. At the moment with some difficulty they can say that the navy can still do what is required of it. However any more cuts and they won't even be able to attempt to argue that. The worse case cut that I can imagine is going down to 10 frigates.

      Also remember that the last Type 26 isn't due to be built until the 2030s, so if they cut the number of frigates now or in 2015/2016, then all they are saving in the near term is the operating costs of the Type 23s. They will still have to build the Type 26s with maybe a small delay, but that delay could well end up costing more than not delaying. As has happened in the past; the delay on the aircraft carriers for example. Plus the fact that from around 2015, the ship yards could have to start laying off people if they don't get new work. So I would think that even if they cut down the number of frigates to 10, they would still be building the Type 26 as planned, with a entry into service of around 2020.

      Delete
    8. Ref: to swapping some Type 26 for smaller corvettes. I used to think this might have been a good idea, but now think it would be a mistake. It would, as a lot off people argue, just be too easy for people to think that they could do the job of the Type23/26, so that we didn't need those or so many. When these smaller corvettes were less than half the price. There is also the problem of what real role do large patrol ships or corvettes play in a more complex combat operation.

      Instead, if there was ever any money to spare, I think it should be invested in improving the RFA fleet. I don't think the number of Type 23/26 should be reduced for this though.

      First I think the existing RFA fleet should be improved so they can better conduct patrol duties. Most are now getting Phalanx fitted, so I would continue that and make sure all the ones that can, have that. Then I would add/improve a combat management system. Next I would give them all the ones that could be fitted, a decent radar. Either Artisan or if it was cheaper (including the support cost of operating a new radar) Sea Giraffe. Failing those two options, maybe even fitting the Type 996 as they are removed from the Type 23s. Although again support costs might make that not worth it. Then I would add Sea Ceptor to all those ones that had the room. I would think most could spare a bit of room for a handful of cells.

      Have no idea of the cost of the above, but I'm thinking maybe ~£30m per ship.

      After those changes, any money left, I would use to to buy some more RFA vessels. Whatever type is required most. So maybe bring the Solid support vessels forward (but keep the existing ones in service too), maybe more tankers, or maybe a new improved Bay class. Make changes to the design so that it supports sea basing better, and so that it can be argued that it isn't just saying that selling the Bay to Australia was a mistake (although it was). So say 4 Vessels of whatever type. But make sure they have all the above improvements, plus space for a modular system. Something like the StanFlex system. Then make a Sea Ceptor module for that. Plus buy some gun modules (either 57mm or 76mm).

      So then most of the RFA fleet should be able to take on any patrol duties or basically any of the tasks that new patrol ships or corvettes could do. Plus they have a clear role in combat operations.

      What is going to be more useful, a improved Bay class with a hanger, Sea Ceptor, Phalanx, Radar, CMS, or a small corvette with most of those same systems (although maybe only either Sea Ceptor or Phalanx)?

      I wouldn't think there would be that much difference between the price. Going with say £1B, maybe we would only be able to get 4 new Bay classes(plus the updates to older ships) against 6 Corvettes, but I would still pick the 4 Bays. Even if they had to be built in Korea to keep the costs down.

      One argument that people use against using RFA vessels for patrol duties, is that of image. As a corvette looks more "fighty" than a support vessel. But is that really a big issue? What would other countries find more useful, us adding a small corvette to the other handful of corvettes or frigates that have been supplied, or providing a Bay class, with all/most of the abilities of a corvette, plus a couple of 15m combat patrol boats in the dock?

      The RFA fleet would then take over completely the east Africa pirate hunting task and the Atlantic Patrol Task (North).

      Delete
    9. How do you propose sufficient ASW protection with corvettes--can corvettes escort the CVF/CVFs? Or can they take on the role of the South Atlantic patrol ship, ie, the Falklands patrol vessel?

      My view is that if the RN leadership is logical, they should send a Type 45 to the Falkllands once the CVF is up. Use a Type 23/26 the most unless there are war signs. Save the cost of Type 45s to patrol the Med, Middle East and possibly SEA Pacific.

      Delete
    10. I still think that 10 Type 26s is a best-case scenario and we could end up with fewer than that. I'm sure axing 3 Type 23s as well as the T22s was one of the options on the table for SDSR 2010, so there is no reason why this could not come up for reconsideration in 2015. If more cuts are needed what is the RN going to be able to offer as an alternative?

      As far as more RFAs are concerned I think we will be lucky to get 3 SSS to replace the existing Forts on a 1:1 basis. The existing ships will be life-expired by about 2020 so keeping them in service any longer than that is not a realistic option. Anything more than 3 new ships is extremely unlikely given the very limited room for manoeuvre that there will be for as far ahead as it is possible to see.

      Delete
  4. Guys - I would completely concur with the more pessimistic comments noted above. I'd suggest the best we could hope for would be 8-12 Type 26 combined (very hopefully) with 10-14 Global Corvettes/MHPC....

    ReplyDelete
  5. Much appreciate your research and articles.

    There was a plan to modify the MK41 to take the proposed longer range Raytheon SM-3 Block 11B ballistic missile interceptor with an ISD of 2020. With a diameter increased from 21" dia. Block 11A to 27" for the Block 11B with an advanced 2nd stage liquid propellant motor. It was cancelled in March, may be in part to Russian objections due to the effectiveness with its longer range that it could have against their intercontinental ballistic missiles especially when one system is slated to be based in Poland, a system is currently being constructed in Romania and a squadron of Burkes permanently home ported in Rota,Spain. As I understand the Block 11A (jointly developed with Japan) has only the range to intercept intermediate range ballistic missiles e.g. North Korea and Iran. Following the success of Block 1B in trials there have been hints it might be reinstated.

    The point of interest being the MK41 has the space to allow for the increase in diameter which I would not have expected.

    ReplyDelete
    Replies
    1. It would have been interesting to see how much modification the MK41 launcher would have required for such an important expansion. It seems to me inevitable that it would have become, essentially, a new system, with a larger deck area, but maybe unchanged height of the module.

      In the future, we will certainly see some other plan going in this direction. I wonder if, however, in the end, the MK57 launcher, with his much bigger cells, will be mandated for the Burke Flight III (or whatever ship actually comes around) in place of the MK41...

      Delete
    2. If America does transition to the Mk-57 size, then that would have the unfortunate consequence of meaning that the Mk-41 would no-longer future-proof against new American missiles.

      Delete
    3. But it'll take decades before the MK41 ceases to be very much the centerpiece of the US fleet, considering how many ships use it and how many weapons it has, ready to be used.
      I don't think a wholesale passage to MK57 is on the cards yet.

      Delete
    4. Oh indeed not - but for some roles, e.g. ABM, the missiles may be sized for the Mk-57 launcher.
      So when thinking about the Type-45 Destroyer, it may be preferable to fit a single 8-cell Mk-57 rather than a pair of Mk-41's.

      Delete
    5. The MK57 is manufactured in modules with four cell each, so to have 8 cells it is two modules. In fact, on DDG-1000, it's 20 modules for 80 cells in total.

      Delete
    6. Ah, so it might be possible to fit 3 x 4-cell Mk-57s on the front of the Type-45? (rather than 2 x 8-cell Mk-41.)

      Delete
    7. It might be. But the MK57 modules are longer, so they need even more space below deck.

      Delete
  6. Gabrielle, the Sylver cells are spaced so far apart on T45 because her VLS spaces are spec'ed for up to 9 A50 units. The three extra units would sit between the two existing rows. That's all I can say publically I'm afraid.

    ReplyDelete
    Replies
    1. You'd need to completely rebuild the silo, to move the current launchers further off to the opposite sides, assuming it is actually possible. It is enough to look at the photo to tell with no room for doubts that the space between the current two rows, as it is now, is large but completely insufficient for installing more launchers.

      Delete
    2. Sorry, but incorrect. The silo dimensions were sized specifically for a 3x3 arrangement. The deck coanings make the units appear bigger than they actually are. The coaning would be altered should the additional units be installed. There is no requirement to widen the deck footprint.

      Delete
    3. It is not like i don't want to believe you, but it is not just the coanings. I'm looking at the cells, and even if they were installed back-to-back in MK41 fashion, i'm really not sure there would be enough space. If there is, then better. But why the spacing between Sylver modules on other warships, which do not have any ambition of growth in cell numbers, then? A reason of some kind must be there, surely...?

      What about the space left on the 45s for the 16 MK41 Strike Lenght cells? People who say serves or served on board HMS Daring say that there is space reserved for installing them, abreast, in front of the existing silo (altering it and the deck footprint, in this case) with the empty space under deck being used currently as a second gym. If this is true too, Type 45s should be able to be fitted with as many as 88 cells in total (space-wise at least, weight and other issues might or might not surface), a far different number from the 64 to 72 normally quoted.

      Delete
  7. I can't speak for how others have approached their Sylver installations, though I can think of several possible reasons for their approaches. The 64 -72 figure is correct but for Sylver only. The use of the forward compartment for further VLS is possible and would be the space used if Mk.41 (for example) was contemplated. The available silo space between the current A50s is only ever intended for further A50s, the fitting of which is extremely unlikely outside a major change of operational requirements.

    ReplyDelete
    Replies
    1. So, correct me if i'm wrong:

      the main silo has no empty space below. It can't take anything longer than A50, but could fit a further three A50 modules.
      And there is further space allocation ahead of the main silo for 16 strike lenght cells, either MK41 or A70, without "bumping" the main gun spaces and its ammunition magazine. Right?

      Thank you, by the way. Very interesting.

      Delete
    2. The fitting of any VLS in the forward space wouldn't have an impact on the magazine at present but would have an impact on the gun due to the changes to the silo superstructure. All of the silo compartment is capable of taking strike length VLS.
      HTH

      Delete
    3. I'm not the same Anonymous and have no idea of how much space there really is, but just to confuse things a bit more, I have seen a number of references to there only being enough space for 12 more cells in front of the existing one; although maybe this is related to the size different between SYLVER and MK41. Maybe 16 A70 could be fitted but only 12 MK41?

      http://webarchive.nationalarchives.gov.uk/+/http://www.royalnavy.mod.uk/operations-and-support/surface-fleet/type-45-destroyers/hms-daring/departments/the-warfare-department

      I also read another recent official pdf file that mentioned the same number, but can't find or remember what paper that was in now.

      Delete
    4. 12 is a very weird number for systems that come in modules of 8 cells each. I think it most likely is simply an error.

      Delete
    5. ...I was about to say that. Since the launchers come in 8-cell modules, it would have to be either 8 or 16, 12 looks like an error.

      Delete
    6. Looking at photos of the Type 45 VLS compartment it is clear that there is NOT enough room for additional cells between the current ones. The only spare space for additional cells- if there is such a thing- is directly behind the main gun.

      Delete
  8. Thanks for going into this in depth, and thanks also to those commenters who have added to it.

    In terms of future-proofing, the "risk" is of a future US missile that we really want, that won't fit in the Sylver, but which will fit in the Mk-41.
    (If it is sized for the Mk-57, then we are out of luck regardless.)
    To me, this seems fairly low.
    MBDA seems to be slightly ahead of the US at them moment*, and the French requirement is in any case going to drive MBDA to fit the form-factor of Sylver. All our planned future development seem to be based on MBDA, and smallish warheads so as to minimise collateral damage.
    The only exception to this being vague ABM desires, but that seems to drive for very large missiles - the US seems to be planning on the Mk-57 form-factor for that.

    The current issue is: Tomahawk or Scalp-N.
    Which depends upon the export price of Scalp-N (unknown to me) and the actual differences in range, accuracy, stealth, reliability etc. (unknown to me).

    (* IMHO only, based on comparing: AIM-9X vs. ASRAAM & IRIS-T; AMRAAM vs. Meteor; SM-6 vs. Aster; Storm Shadow vs. AGM-158 JASSM; Hellfire vs. dual mode brimstone,)

    ReplyDelete
  9. The MK41 is one of the most lethal weapons in modern day, capable of launching 61 guided missiles with pinpoint accuracy within one minute. Very impressive system.


    Link

    ReplyDelete
    Replies
    1. It's not quite like that.
      The term "Mk-41" does not refer to the whole system, but just one component, the launcher/container modules.
      Each module holds 8 missiles (although smaller missiles can be 4-packed into each standard missile silo, so 32 smaller missiles.)
      So "a" Mk-41 can fire 8 large missiles before it has to return home for reloading. But the ship has anywhere between 4 and 16 of these Mk-41 launchers.

      These Mk-41 launchers has no impact on the accuracy of the missiles.
      The guidance and accuracy varies by missile. (It isn't literally 'pinpoint' but I guess you knew that.)
      For anti-air missiles, the ship will carry between 2 and 4 'missile director' radars, so the system as a whole can only guide 2-4 missiles in flight at a time. (But later missiles can guide themselves when they get close enough, and also the missiles know to 'keep going in straight line" if they aren't being guided.)

      Delete
  10. I wonder if the Mk57, which is designed to blow outwards if hit, can be fitted centrally in a ship or if they can only be fitted edgewise.

    ReplyDelete
  11. Gabriel,

    I just did a very rough measurement on the photo you posted above and it appears that there is just enough space for an addition 24 cells between the current two rows. However, the cells would be back to back and the coanings between them would have to be completely removed.

    ReplyDelete
    Replies
    1. It's the same result i've obtained, also looking at the drawings of Type 45. The cells would have to be packed with the same density of a MK41 installation, though, being all back to back, and i've never seen it done, so far at least, with Sylver. I'm afraid there's no certainty at the state about whether it is possible or not.

      Delete
  12. I think the UK should obtain/procure at least 18 Type 26 Frigates.
    I would deploy thus:
    Falklands duty - 1 (6 month deployment) then rotated with another so 2 assigned
    UK nuclear deterrent - 1 + 1 on standby if there are any issues
    UK Carrier group - 2 - assigned for 6 months + 2 Type 45
    UK Defence - 2 - 1 north and 1 south (along with 2 Type 45)
    Nato standing Forces - 1 assigned to each (so 2)
    This would leave 8 to be rotated in and out say every 3 months.
    I would also add the 7th and 8th Type 45 (btw do you know when the last date to exercise this option expires?) and increase to 10 Astute SSN. Also a small class of corvette (say 8 ships) for low level ops.
    18 Type 26 would provide good capability and a surge if required (i.e. Libya) and overall 36 ships + 14 submarines (SSBN inclusive) would help position the UK as a strong moderate power.
    Cut the aid budget by 1/2 to fund the extra ships.

    ReplyDelete
    Replies
    1. Increase your own tax to fund the extra ships. Launch nuclear weapons against AFghanistan to stop Taliban for ever.

      Delete
  13. Great to find that now we have vertical missile launching system.

    Thanks
    Bruce Hammerson

    Hydraulic Installation Kits

    ReplyDelete
  14. Where is the weight of missile supported in the launcher consisting of 8 missiles? Is it supported at the top of the launcher

    ReplyDelete

  15. Thanks for the post, I will look forward to see more posts from your blog and and also about
    ivco jebel ali Generators

    ReplyDelete
  16. Thanks for the post, I will look forward to see more posts from your blog and and also about
    ivco generators Generators.

    ReplyDelete
  17. https://www.youtube.com/watch?v=PxSsHeiioG0

    From minute 3:40 onwards, the video shows the under deck arrangement of Sylver A 43 on the Aquitaine class ships.

    I hope it helps you somewhat.

    ReplyDelete

Everybody can comment on this blog without needing a Blogger account. It is meant to keep the discussion free and open to everyone. Unfortunately, anonymous accounts keep the door open for spammers and trolls, so i'm forced to moderate comments and approve them before they appear. Apologies for the inconvenience.